Here is my "route print" without dialup connected:
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x2 ...00 17 31 1b 45 cd ...... Marvell Yukon 88E8001/8003/8010 PCI Gigabit Ethernet Controller - Packet Scheduler Miniport
===========================================================================
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.0.13 192.168.0.14 20
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.168.0.0 255.255.255.0 192.168.0.14 192.168.0.14 20
192.168.0.14 255.255.255.255 127.0.0.1 127.0.0.1 20
192.168.0.255 255.255.255.255 192.168.0.14 192.168.0.14 20
224.0.0.0 240.0.0.0 192.168.0.14 192.168.0.14 20
255.255.255.255 255.255.255.255 192.168.0.14 192.168.0.14 1
Default Gateway: 192.168.0.13
===========================================================================
Persistent Routes:
None


And again, but with dialup connected:
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x2 ...00 17 31 1b 45 cd ...... Marvell Yukon 88E8001/8003/8010 PCI Gigabit Ethernet Controller - Packet Scheduler Miniport
0x20004 ...00 53 45 00 00 00 ...... WAN (PPP/SLIP) Interface
===========================================================================
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.0.13 192.168.0.14 21
0.0.0.0 0.0.0.0 4.245.113.154 4.245.113.154 1
4.245.113.154 255.255.255.255 127.0.0.1 127.0.0.1 50
4.255.255.255 255.255.255.255 4.245.113.154 4.245.113.154 50
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.168.0.0 255.255.255.0 192.168.0.14 192.168.0.14 20
192.168.0.14 255.255.255.255 127.0.0.1 127.0.0.1 20
192.168.0.255 255.255.255.255 192.168.0.14 192.168.0.14 20
209.247.21.245 255.255.255.255 4.245.113.154 4.245.113.154 1
224.0.0.0 240.0.0.0 192.168.0.14 192.168.0.14 20
224.0.0.0 240.0.0.0 4.245.113.154 4.245.113.154 1
255.255.255.255 255.255.255.255 4.245.113.154 4.245.113.154 1
255.255.255.255 255.255.255.255 192.168.0.14 192.168.0.14 1
Default Gateway: 4.245.113.154
===========================================================================
Persistent Routes:
None


Any help deciphering which routes i might want to try to change would be much appreciated. Do you think, using the route command, if i used METRIC along with the -p flag (persistant), that i could permanantly change the metric for the appropriate routes related to my dialup? Or would i have to reset them every time i conecct the dialup? Not a big deal; i can setup a batchfile.

Thanks again for the help.