[RESOLVED] Motherboard, CPU, Memory

[SuperSparks]

The default speed for the memory on the i7-900 series is 1066. Overclocking the memory on its own is a bit unorthodox, and I'm not really sure that it's worth doing TBH. It would be better to leave the memory multiplier be, and simply increase the main clock, which will then overclock the CPU and memory together. You should be able to get a worthwhile O/C on stock voltages - I got 15% out of mine without any effort at all.

[Falcon Speed]

The default speed for the memory on the i7-900 series is 1066.

Overclocking the memory on its own is a bit unorthodox, and I'm not really sure that it's worth doing TBH.

What is TBH?

It would be better to leave the memory multiplier be, and simply increase the main clock, which will then overclock the CPU and memory together.

I changed the "Memory Multiplier" back to "Auto".

I would still need to do the following right so that the memory would match the recommended SPECs from OCZ, right?

DRAM Timing Selectable (SPD) – Expert (necessary to change the following Timing Settings: )
Channel A Timing Settings - CAS Latency 8, tRCD 8, tRP 8, tRAS 24, Command Rate 2
Channel B – same
Channel C – same

Should I change BOTH back to "AUTO" because OCZ specs is 1.65 for the volt.

QPI/Vtt Voltage – 1.335V
DRAM Voltage – 1.640V

Thanks Nick

[SuperSparks]

TBH = To Be Honest

I would set both back to auto for the moment. Messing with the memory settings is getting into the realms of advanced overclocking, and it's probably more sensible to start with the basics

[Falcon Speed]

TBH = To Be Honest

I would set both back to auto for the moment. Messing with the memory settings is getting into the realms of advanced overclocking, and it's probably more sensible to start with the basics

Yeah, I don't want to overclock and did not know that is considered as overclocking the memory. I thought I was setting it to specs. So, should I still set the latency of the memory to the OCZ specs?

[SuperSparks]

If you leave the BIOS settings at Auto, it should take care of latency, etc.

[Falcon Speed]

I just would like to thank everyone (especially Nick, jdc2000 and Train) on this thread for helping me on this topic. My semi-new computer is back up and going. I learned one thing from Nick is not to overload the rails on the power supply. Learned alot from this thread. Thanks guys.

BTW... Nick, do you use EasyTune6 to monitor your CPU and Hardware temperature? Otherwise, what do you use? Also, what is the average temp for an i7-930? Mine is running at between 49-60 celsius.

[SuperSparks]

I tried EasyTune once, but I didn't care for it. I use these, HWMonitor and RealTemp are my favourites, but running OCCT occasionally is always worthwhile, as it really stresses the CPU, so that you can be sure that the computer will always be within acceptable temps, whatever you throw at it.

Real Temp

CPU-Z

HWMonitor

OCCT

49 to 60 is fine. Start to worry if the core temp goes over 85C.

[SuperSparks]

BTW, did you ever see this old thread of mine:

http://discussions.virtualdr.com/sho...t=watercooling

[Falcon Speed]

BTW, did you ever see this old thread of mine:

http://discussions.virtualdr.com/sho...t=watercooling

After seeing that thread, I really admire and respect you as a true hobby enthusiast. That is so cool! What else did you add to your Antec because I see couple of other things in your 5.25 bayer area.

Bistro first comment was funny.

Also, is this for real? I never knew you could do this? How come there is no electrical surge or problems? Is it a good cooling system?
http://www.pugetsystems.com/submerged.php

In that thread, it also mentioned about this:http://www.arctic-cooling.com/catalo...th=39_&mID=127
What is your take on it before I run out and get it?

[SuperSparks]

In my 5.25" bays I have drive caddies, 2 DVD burners and the IO bay for the Creative X-Fi.

Because mineral oil is non-conductive, there are no electrical problems. If memory serves, there are other, less messy, liquids that you can use too, though they are exotic and expensive. It is a good means of cooling, but really is a solution for the serious overclocker, I think

Myself, I've been happy with Arctic Silver for a few years. TBH, the real-world difference between any of the top quality compounds is pretty slight.