-
August 8th, 2005, 05:29 AM
#1
Error 36:sharing buffer overflow
am trying to setup my machine to access a network share from DOS so that I can perform a Ghost of my hard drive.
I am using MSDos 3.11 and my TCP/IP stack is setup correctly, because I can ping the machine from another machine on the network.
When I type the net logon command it tells me that the workstation service has not been started and asks me to start it. When I respond I get the following error message:
Error 36: The system has detected an overflow in the sharing buffer.
-
August 8th, 2005, 06:29 AM
#2
DOS3.11 ? That's ancient (Compaq DOS ?), or is it a DOS/Win3.11 (DOS 6.xx)?
Anyway, have you tried increasing either the /F: or /L: values on SHARE.EXE?
http://www.vfrazee.com/ms-dos/6.22/help/share.htm
-
August 9th, 2005, 07:48 AM
#3
that is microsoft network client for MS-DOS version is 3.11
redirector version is 2.51
i tried share command but not avilable.says bad command.
any other solution
-
August 9th, 2005, 09:51 AM
#4
Originally Posted by niranjan
any other solution
No, sorry, too small a SHARE.EXE buffer was all that occurred to me with my miniscule DOS network experience. Someone else may have more ideas.
-
August 9th, 2005, 08:22 PM
#5
Don't know what's going on but I have a couple of questions.
What operating system is running at the computer where the share is located?
Do you have any net start command or net start workstation command on the MS-DOS client in the autoexec.bat file?
Can you provide the exact wording of the message?
Is the client strictly an MS-DOS workstation? No Windows?
Maybe the following links can help.
http://support.microsoft.com/default...b;en-us;238640
http://support.microsoft.com/default...b;en-us;183858
http://support.microsoft.com/default...b;en-us;135465
Last edited by Robert M; August 9th, 2005 at 10:42 PM.
Reason: Adding Info
Open your mind, not your computer.
-
August 10th, 2005, 09:11 AM
#6
hi
microsoft network client for MS-DOS version is 3.11
redirector version is 2.51
is loaded on windows 95 it si in flash.
we have an IO system designed for a specific application.it consists two nodes for redundency.one is working fine with same config.sys and autoexec.bat files.
we connect to remote servar using
net use * \\servername\sharename.
please look at config.sys and autoexec.bat files mentioned below.
my config.sys file is
Config.sys
.....................
Device=c:\dos\himem.sys \testmemff
Dos=high,umb
Device=c:\dos\emm386.exe noems
Files=30
Buffers=3
Lastdrive=z
Shell=c: \command.com /p /e:1024
Devicehigh=c:\dos\ifshlp.sys
and my autoexec.bat file is
.............................
@echo off
cls
path=c:\;c:\dos;c:\net;c:\tools
smartdrv /u
set TEMP=C:\TEMP
REM lh keyb sv
lh doskey /insert >NUL
set COMSPEC=c:\command.com
net initialize
netbind
umb
tcptsr
tinyrfc
nmtsr
emsbfr
net logon /savepw:no /yes
thank you and regards
niranjan
-
August 10th, 2005, 04:39 PM
#7
Hmmm...
No "net start" command in the autoexec.bat file.
What OS is running at the share you are trying to reach?
I think you should have a command in the autoexec.bat file similar to one of the following somewhere before the net logon command.
net start workstation basic
net start workstation full
Have you recently edited the autoexec.bat file or run a setup or install program which may have modified it?
What is the name of your redirector file?
Are you trying the net logon command at a command prompt after you begin the graphic user interface for Windows 95? If so, I don't think that method will work. You should use the F8 key and boot to command prompt only before trying it.
Here's some other information
http://support.microsoft.com/default...b;en-us;131035
http://support.microsoft.com/default...b;en-us;122494
http://support.microsoft.com/kb/122123/EN-US/
http://support.microsoft.com/default...b;en-us;124175
Where are you reading the following version information you posted? You said:
microsoft network client for MS-DOS version is 3.11
Last edited by Robert M; August 10th, 2005 at 05:35 PM.
Open your mind, not your computer.
-
August 11th, 2005, 07:04 PM
#8
Someone in Germany (I think) has seen that Error 36 message.
He referred to a Microsoft KB article written in German (I think) here.
http://techsupport.softservice.de/kb...5&cNode=8P1T2M
This seems to be the relevant Packet Signing information in english at the link below. Apparently the Network Client for MS-DOS cannot deal with SMB signing or something like that.
http://support.microsoft.com/default...b;en-us;887429
Open your mind, not your computer.
-
August 12th, 2005, 02:24 AM
#9
i am giving net start command at c:/NET> prompt.
it says
The WORKSTATION service is not started.
Is it OK to start it? (Y/N) [Y]:
Error 36: The system has detected an overflow in the sharing buffer.
i have never edited autoexec.bat file and with same file it is working with other node.
there is no redirctor file it seems. how to find it?
at c:/NET>net ver
gives
microsoft network client for MS-DOS version is 3.11
i am getting same error as like mentioned in german.but i dont know german.
-
August 12th, 2005, 09:37 AM
#10
Here's my understanding:
Two redirectors can be started with the net.exe file.
One for Netware and the other for Microsoft.
The redirector which loads depends on the choices made at setup time when the program was installed.
By the way......
That net ver command on my computer returns a different result.
I have Windows 95 on my machine. It yields version 4.00.950.
I wonder if you have the wrong version of the net.exe file?
Your CONFIG.SYS entry for Buffers 3 doesn't seem right.
Not sure though.I posted some information in English also.
Where are you getting that version 2.51 info?
Open your mind, not your computer.
-
August 16th, 2005, 02:42 PM
#11
Did you do a line by line comparison of the config.sys file with the computer that seems to be working? What are the differences?
Do you have a file called protocol.ini in the C:\NET directory?
Last edited by Robert M; August 16th, 2005 at 02:49 PM.
Open your mind, not your computer.
-
August 16th, 2005, 03:51 PM
#12
Open your mind, not your computer.
-
August 17th, 2005, 12:28 AM
#13
hi Robert
yes i compared both config.sys files.They are exactly same. yes i have protocol.ini file in c:\NET directory.
-
August 17th, 2005, 05:42 PM
#14
You are booting with a floppy disk or a hard drive at each?
Compare all the files in the C:\net directory at each location
Compare the contents of the PROTOCOL INI files at both locations.
First, you better back up the PROTOCOL.INI files at both locations.
Make a copy of the PROTOCOL.INI file at each location and call them protocol.xxx
You should be able to open the PROTOCOL.INI files with the Windows notepad.exe program or the MS-DOS edit program. Be careful not to change the contents and do not open them with a word processor such as word.
Once they are open with either of these programs, you can save them with a new name.....PROTOCOL.XXX...to make a copy of them.
What kind of network adapter is being used at the station displaying the message? What speed? How about at the node with no problem?
Identical computers? Where did you read the version 2.51 info?
How did you obtain the MS-DOS client...download or from a Windows NT Server CD-ROM? Both locations?
Last edited by Robert M; August 17th, 2005 at 06:39 PM.
Open your mind, not your computer.
-
August 19th, 2005, 02:35 AM
#15
we are booting with flash on special board,all files are exactly same.it is loaded by the manufaturer itself.
i am getting version info on at c:\net dos prompt.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|