-
September 25th, 2000, 09:21 PM
#1
Printer prints but no ink on paper!!.....new ink pak!!
Hi all....just bought a Canon BJC 2100 and i got it set up and everything....all my port configurations and proper drivers are installed....when i try to print something it sends it to the printer and i can see the job in the print queue and the printer starts printing and prints the whole page but NO INK is written on the paper....it did all the proper movements as if it were really printing ....the only difference is that no ink is coming out on the paper....i've checked the cartridge and i can touch the bottom of it and i can touch the ink itself on the edge of the writing part....anyways i've removed all the tapes on that writing part but still no ink comes out of my cartridge.....really confused up here guys....would appreciate some help if yall not too busy
thanx
Joe
-
September 25th, 2000, 09:41 PM
#2
Trialzone, sounds to me like you have gotten hold of a bad cartridge. If I were you I would see about exchanging it. I have a Canon BJC4400 and believe me if you touch the bottom of the cartridge you are gonna get ink on yourself if it is working properly. Probably not what you wanted to hear but its just MHO.
Chrissy
What a wonderful thing learning is.!!!
Chrissy
-
September 25th, 2000, 09:47 PM
#3
the thing is when i touch the bottom of the cartridge i do get ink on my fingers...but it just won't write it on the paper
it might be a bad cartridge as your saying or some weird thing going on with the hardware
lol
-
September 25th, 2000, 11:09 PM
#4
Have you removed the piece of clear plastic from the bottom of the cartridge.
Win 7
Asrock Z68 Extreme3 Gen3
I5 2500k @4ghz
8Gb DDR3 2133Mhz
Crucial M4 128Gb SataIII SSd
Sapphire Radeon 6870
Samsung 931bf 19" LCD
-
September 25th, 2000, 11:25 PM
#5
yes i have done that.....it's weird that it's still not printing
-
September 26th, 2000, 05:21 PM
#6
Try booting directly to DOS and sending soemthing to the printer. That would help you determine if it is a WIndows Driver problem or a mechanical problem with the printer.
When you print DIRECTLY from DOS, you are actually printing real native text, however, when you print text from Windows, it is converted into graphics.
If you don't have a DOS program that can print text, try this on the command line-
copy autoexec.bat LPT1
this is assuming that your 'autoexec.bat' file actually has something in it. You could substitute config.sys or msdos.sys in place of autoexec.bat.
-
September 27th, 2000, 12:21 AM
#7
Sorry but I think the correct syntax is
copy autoexec.bat > LPT1
Unless this has changed in DOS 7 (win95) the output of the copy command has to be directed to a new device if you want that device to get the input from the command
This also assumes that there is something in the autoexec.bat file.
In the case of 95+ it is preferred that both autoexec.bat & config.sys are empty
I think you are doing something fundamentally wrong. Like the tape isnt off the cartridge, or something like that although you said it was
This is not a windows 95 problem in other words
Check the basic simple setup stuff for the printer again
Sure sounds like that the problem is with the cartridge itself because the printer acts like it is working.
The thing about the jet printers is that the little copper thingy on the bottom of the cartridge is the print head itself.
You should never touch it. Oil from your pores can cause the cartridge to clog
I would suggest trying a new cartridge right off & chalking the old one off if a new one works
In the beginning there was the command line
-
September 27th, 2000, 03:21 AM
#8
Hey Trialzone,
I got a BJC 2000,
Check your book for directions on clearing the inkjets.
Also, through experience I have found that touching any of the printed circuit on the side of the cartridge will screw it up and it will not print! I tried cleaning it with alcohol and everything but it didn't work, I had to replace the cartridge, and I learned to just pull out the ink wells and leave the cartridge alone!
Good Luck,
Dave
------------------
Windows Tips *** Help others less fortunate.
*** Help others less fortunate.
JESUS IS LORD !
-
September 27th, 2000, 07:43 AM
#9
Try running a hot iron over the page, it might be invisible ink!! Sorry couldn't resist that. I would take it back, have it replaced and see what happens.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|