Search Results - Virtual Dr Forums-Computer Tech Support

Search:

Type: Posts; User: cirelli1

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    303

    hard drive trouble

    I'm trying to fdisk a hard disk and then format and install win 95. I get a c:\prompt and then any thing I try to type I get this error.
    "type the name of the command interpreter (e.g.,...
  2. Thread: keyboard

    by cirelli1
    Replies
    3
    Views
    441

    Yes I tried another keyboard with the same result...

    Yes I tried another keyboard with the same result I will next look at the connection it is a ps/2type connection on the motherboard so I'll check that next.
    I'll let you all know
    thanks
  3. Thread: keyboard

    by cirelli1
    Replies
    3
    Views
    441

    keyboard

    EVERY time I start my computer (486, 20mb ram windows 95c)and I mean every time, the key board doesn't work,,,I have to go to device manager remove the keyboard (it never shows any conflicts,,no ! no...
  4. Replies
    9
    Views
    476

    The jumpers were set correctly. HDD-master and...

    The jumpers were set correctly. HDD-master and the cdrom-slave. And I believe there was only one ide connector on the machine that the drive wouldn't work in...as I said I put it into a different...
  5. Replies
    9
    Views
    476

    I believe it said it was the d:drive which was...

    I believe it said it was the d:drive which was the cdrom. I do not think it was the secondary IDE controller as the drive was connected to the second connector on the cable attached to the primary...
  6. Replies
    5
    Views
    523

    that upgrade is also on the bluelight.com cd...

    that upgrade is also on the bluelight.com cd available at any K-Mart
    explore the cd and open the "updates"folder and there it is https://discussions.virtualdr.com/
  7. Replies
    9
    Views
    476

    Thanks to all for all the help. I still can't...

    Thanks to all for all the help. I still can't get that to work in that machine,,,BUT,,,I put the same cdrom into another machine with a pentium chip and it WORKED....go figure.
    Thanks again ...
  8. Replies
    9
    Views
    476

    It is a mitsumi J05 / I02, the only numbers on...

    It is a mitsumi J05 / I02, the only numbers on the drive.
    I emailed mitsumi and they replied it is PnP and needs no additional drivers. Will keep you updated.
  9. Replies
    2
    Views
    415

    Have you tried going into device manager and...

    Have you tried going into device manager and remove the mouse and re-boot? Windows should reconize and install the mouse.
  10. Replies
    9
    Views
    476

    I tried all the above possibilities with no luck....

    I tried all the above possibilities with no luck.
    What I did is blew out the hard drive and started over. The cdrom works in dos and I am able to install windows 95. When windows 95(not DOS) starts...
  11. Replies
    3
    Views
    827

    Mitsumi's web site has a diagnostic program that...

    Mitsumi's web site has a diagnostic program that you can down load. I did and it works.
  12. Replies
    9
    Views
    476

    windows 95cdrom trouble

    I recently obtained an older system 486 66mh, I wiped out the hard drive and re installe win 95, installed some other software and then the cd-rom stopped working. checking "my computer" it shows the...
  13. Replies
    2
    Views
    2,405

    Right after you turn the system ON, numbers...

    Right after you turn the system ON, numbers should be counting in the upper left hand corner, it will count up to the amount of RAM you have in the system. Then the cursor will jump to the upper...
  14. Thread: Memory

    by cirelli1
    Replies
    3
    Views
    926

    To load TSR's high you use the loadhigh (or...

    To load TSR's high you use the loadhigh (or lh)command example;
    loadhigh c:\dos\doskey.com
    or lh c:\dos\doskey.com
    good luck
Results 1 to 14 of 14